Elemental Workshop II/Quick guide

From Old School RuneScape Wiki
Jump to: navigation, search
Instruction manual.png
This quick guide has an in-depth guide here.
It contains a more detailed description of dialogue, cutscenes, and storyline.

Details[edit | edit source]

Walkthrough[edit | edit source]

Starting out[edit | edit source]

Bookcase containing the Beaten book.
  • Go to the Exam Centre south of the Digsite. (Varrock teleport then run east; or use a Digsite pendant/ teleport and walk south towards the exam centre; the Senntisten teleport from the Ancient Spellbook is quite close, and can be used from a Portal Nexus in a POH)
  • Search the most northeastern of the southeastern bookcases to find a beaten book.
  • Read the beaten book, then read the scroll.
  • Keep the book.

The second key[edit | edit source]

  • Head back to the Anvil building in Seers Village and enter the odd-looking wall and down the staircase to the workshop.
  • Go north to the water elemental room and search the machinery to the west to get a key.
    • Note: You must read the scroll obtained from the Beaten Book to search Machinery or the option will not appear.
  • If you didn't bring 2 elemental ores with you, go west and get them by killing 2 Earth elementals (Mine the Elemental Rock for them to spawn).
  • Go south from the centre room and smelt your ores into bars, at the furnace.
  • Go down the hatch in the centre room with the key in your inventory.

Making Repairs[edit | edit source]

The crane[edit | edit source]

  • Take-from the schematic crate to the south, take both schematics.
  • Go back upstairs and use one bar on the workbench to make an elemental claw.
  • Return downstairs and use the lever next to the schematics crate to lower the crane (West lever).
  • Use your claw on the old crane.

The junction box[edit | edit source]

Elemental Workshop II - Junction pipe placement.png
  • Climb the stairs to the southwest to get on the catwalk.
  • Open the junction box to the west.
  • Click the pipe ends to connect them as shown.

Pipes and cogs[edit | edit source]

A visual of the correct cog placement
  • Search all crates on the ground floor and the catwalk of the workshop until you find:
  • On the North side of the catwalk use the Pipe on the broken piping.
  • On the East side of the Ground floor use the cogs on the pins as shown.
    • Note: This is on the side of the machine that looks like a wind tunnel.
  • Place the cogs as follows:
    • Small cog on upper left pin
    • Medium cog on lower left pin
    • Large cog on right pin.
  • Pull the old lever to the right.
    • Note: The repairs are now complete. You will no longer need to head up to the catwalk again.

Operating the machine[edit | edit source]

The crane[edit | edit source]

  • On the South side place an elemental bar on the jig cart. (under the elemental claw)
    • Note: Crane controls in case you get stuck:
    • Raise/Lower crane: Western lever
    • Rotate crane: Eastern lever
  • First, use the Western lever (by the schematics crate) to raise the crane.
  • Use the Eastern lever to rotate the crane.
  • Use the Western lever twice to lower the crane into the lava and back up up again.
    • At this point the elemental bar should be orange.
  • Use the Eastern lever to rotate the crane over the cart.
  • Use the Western lever twice to lower the bar onto the cart and release it.
  • Pull the lever just North of the claw controls to move the cart.
    • Note: The lever in front of the yellow sign moves the cart to the next station.

The press[edit | edit source]

  • Pull the west lever to flatten the bar once the cart has stopped.
    • Note: At this point the elemental bar should be flattened.
  • Pull the yellow sign lever again to move the cart to the next station.

The water tank[edit | edit source]

  • Pull the northernmost lever.
  • Turn the corkscrew lever twice.
  • Pull the northernmost lever again.
  • Turn the west water valve to open it.
  • Turn the east water valve to open it.
  • Turn the west water valve to close it.
  • Turn the east water valve to close it.
  • Pull the northernmost lever.
    • Note: At this point the elemental bar should be blue.
  • Turn the corkscrew lever twice.
  • Pull the northernmost lever to close the door.
  • Pull the yellow sign lever again.

Drying[edit | edit source]

  • Pull the East lever
    • At this point the elemental bar should be white.
    • Note: The machine may need to be turned off and back on again for the bar to turn white.
  • Pull the East lever again to stop the fan.
  • Pull the yellow sign lever again.

Finishing up[edit | edit source]

  • Take-from the jig to get a primed bar.
  • Head down the stairs to the northwest.
  • Go through the east door.
  • Use your primed bar with the extractor gun.
  • Operate the Extractor hat with the bar placed under the gun.
    • Note: Your magic level will be drained by 20.
  • Take-from the extractor gun to get a primed mind bar.
  • Go up both spiral stairs

(Note: Make sure you have the beaten book in your inventory. If you only have the slashed book you will automatically make a mind shield and not the mind helmet.)

  • Use your primed mind bar on the workbench to smith a mind helmet.

Quest complete!

Rewards[edit | edit source]

Elemental Workshop II reward scroll.png

Trivia[edit | edit source]

  • When you are downstairs in the corridor that has the mind door, a body door can be seen further down. This is a hint towards the Elemental Workshop III quest, which was released in RuneScape 3. The armour reward from it was a Body body.